Press workflow
Kids wear soft
Soft, safe DTF transfers for kids' apparel depend on gentle handling and fine materials from start to finish.

Start with these
Lines we put together for this job
Children’s wear needs a soft touch, transfers that feel light, flexible and smooth against the skin. Our soft-hand workflow helps your prints last through play and gentle care cycles, perfect for gift packs, school kits and festive drops.

Hot-melt grade
Powder Soft Hand
Fine-melt DTF adhesive powder for soft, wearable prints on cotton-rich tees and lightweight fleece.
View →
Cold-peel film
Film PET 100
For premium cold-peel transfers, Film PET 100 delivers sharp edges, a soft hand and reliability.
View →
Starter set
CMYK+White Compact
Compact 250 ml CMYK+White bottles for new setups and test runs.
View →What makes kids’ wear different in DTF printing
Children’s garments are almost always smaller, softer and cut with more stretch than adult ranges. Common blanks include baby grows, toddler tees, vests, onesies and sleepwear, mostly made from cotton or cotton-rich knits. Parents and schools expect skin-safe finishes, minimal handfeel and lasting colour after many washes. Gift packs and drop-offs for events or festive seasons often run in bulk but with strict quality checks, so any rough patch or stiff transfer stands out. Small print areas, seams and tiny collars make it trickier to get perfect registration and pressure.
You’ll often work with lighter weights and pastels, where a heavy hand or missed edge is easy to spot. Some shops dont realise how much the feel of the transfer matters on these jobs until they see a batch come back with feedback from parents or teachers.
Where DTF transfers go wrong on children’s sizes
Trouble usually starts with the powder or film: if the adhesive is too coarse, or the film is thick and stiff, the transfer will feel bulky and may peel with a harsh edge. Over-curing the powder, even by a minute, can make the print hard and compromise stretch. Missed pre-pressing lets moisture and wrinkles ruin the bond. On pastels and bright whites, any powder overspill or under-cured edge will stand out after the first wash.
It’s easy to rush and skip a test run, but one rough or patchy batch can sink a repeat order for a whole school or club. Always test on the specific garment blank, and watch for static on thin cotton in winter, stray powder can stick to places you don’t want.
- Powder too coarse creates stiff feels
- Over-cured powder stiffens or yellows prints
- Static and dust cause misapplied powder
- Missed pre-pressing leaves moisture trapped
DTF Ink lines we use for soft-hand kids’ runs
For the softest results on children’s wear, we match three DTF Ink lines: Powder Soft Hand, Film PET 100, and CMYK+White Compact ink. The Soft Hand powder is a fine TPU blend that melts evenly and keeps the print flexible, especially on light cotton and cotton-rich blends. Our Film PET 100 is a medium-weight, double-matte PET film, reliable for both A3 sheets and roll-fed jobs, and comes in both hot-peel and cold-peel types for different needs.
For colours and white, the CMYK+White Compact ink set gives solid, non-chalky colours and a strong white underbase, just remember to agitate the white every shift and run a nozzle check before the first job. Start with these typical settings and adjust by garment: cure the powder at 110 to 115 degrees C for 2 to 3 minutes in an oven, or hover under a press at 145 degrees C for 4 minutes, looking for a light orange-peel gloss. Press cottons at 155 degrees C, 12 seconds, medium pressure, and use hot peel if the film allows. Always finish with a 5-second press through Teflon for a soft touch.
- Powder Soft Hand: fine, even coverage for soft finishes
- Film PET 100: double-matte, flexible, A3 sheets or 30 cm roll
- CMYK+White Compact: strong colour, smooth white underbase
- Hot or cold peel options to match job flow
Planning stock and your week for kids’ runs
Most children’s wear jobs land around start of term, sports seasons or the festive rush, so plan stock well in advance, especially the sizes and pastel shades. Schools and clubs often confirm late, so keep a few extra packs of Powder Soft Hand and Film PET 100 on hand. For gift packs or event drops, time your week so all pressing, cooling and QC checks are done in daylight, as fine details are harder to catch after hours.
Schedule jobs in batches to avoid changing powders mid-week, and run regular maintenance on the printer after power cuts or planned load reduction. Always keep spare rolls or sheet packs dry and flat in the print room, and check your press temperature with a thermometer before the first test. A production whiteboard in the lab helps keep on top of orders, especially with small sizes where left and right chest prints can be mixed up easily on a busy day.
Read before you press
Customer reviews
What our DTF Ink customers say
Verified Google reviews
Talk to DTF Ink
Tell us about your printer, film, powder and press settings and our team will help you get repeatable transfers. Meadowdale lab in Germiston, plus seven studios.

