Recipe
Gentler powder curing for kidswear DTF transfers
How to achieve a soft cure on DTF prints for children’s clothes without risking under-cured powder.

I’m Louw Hattingh, the ink chemist at DTF Ink, and I’ve spent plenty of time in the Meadowdale lab developing DTF recipes for trickier garments. Kidswear is one of the main requests from print shops that want a softer, safer feel, especially for younger ages and sensitive skin. Here’s a practical approach to dialling in a gentler powder cure for children’s T-shirts and onesies, while keeping transfers wash-safe and durable for family life.
Adjusting curing settings for softer results
Children’s garments, especially for babies and toddlers, need a finish that feels soft and flexible, the last thing parents want is a stiff transfer. To soften the cure, start by lowering your powder curing temperature and extending the time slightly. Instead of blasting at 140 to 150 degrees C for three minutes, try 110 to 120 degrees C for three to four minutes as a first test, using your oven or a hovering heat press with a 4 to 7 millimetre gap. Watch the transfer through the process: you’re looking for the powder to go glossy and develop a gentle orange-peel effect, but not to yellow or go hard.
Be especially careful with lighter weight cottons and blends. Too high a temperature or too fast a cure can lead to a plasticky feel, and causes the film to shrink or ripple, which ruins detail on small prints and name-badges.
Checking for complete powder melt
Gentler cures run close to the minimum melt point for TPU powder, so it’s vital to confirm the powder is fully melted without burning the transfer. When you think you’ve got your settings right, pull a test transfer and inspect it in good light. The correct finish shows an even, glossy sheen, with no cloudy or milky patches. If you press your nail gently to the cured adhesive, it should not lift any powder and should feel smooth, not gritty.
Under-cured powder is one of the most common problems we see when shops try to lower their cure for kidswear. Transfers with under-melted powder will feel tacky, and the print can wash off or flake after only a few cycles. Over-cure, on the other hand, causes yellowing and a harder, less flexible patch.
Pressing transfers onto kidswear with care
Once you have a correctly cured sheet, focus on transfer pressing. Kids T-shirts, vests and babygrows often have more stretch and lighter fabric than adult tees. Pre-press each garment for two to five seconds at your target temp to flatten seams and remove moisture. For most kidswear cotton, a starting point is 150 to 155 degrees C for 10 to 12 seconds at medium pressure, but always test your specific garment.
If you’re working on polyester or polycotton blends, drop the temperature to 125 to 135 degrees C and cold peel after the transfer cools. This helps avoid shine and dye migration, which show up quickly on lighter children’s colours.
A second finishing press, five to eight seconds through a Teflon sheet, improves feel and gives better edge durability, reducing the chance of the transfer lifting during repeated washing and rough play.
- Check platen temperature with an infrared thermometer for cold spots
- Always cold peel on synthetics to reduce scorch risk
- Use a Teflon sheet for all finishing presses
Adapting to South African print room conditions
Local climate plays a role in gentler powder cures. In Highveld winters, dry air can cause static that makes powder cling unevenly or scatter, a light mist of distilled water in the air can help, but don’t spray the film directly. In coastal humidity, powder tends to clump and can slow the cure; store opened powder sealed and use silica gel in storage bins if you’re near the sea.
Keep your print room at about 45 to 60 percent relative humidity and 20 to 25 degrees C if possible. A wall hygrometer is worth the small investment. If you get power cuts, cover printers and open ink bottles immediately and re-run your white ink circulation once you’re back online, white is especially prone to settling if left idle.
Finally, do a wash test: print, cure and press a sample, then wash it inside out at the garment’s labelled temperature and check for edge lift and cracking before starting a run. This is the best way to confirm you’re striking the right balance between soft hand and long-lasting prints.
Related
Talk to DTF Ink
Tell us about your printer, film, powder and press settings and our team will help you get repeatable transfers. Meadowdale lab in Germiston, plus seven studios.


